>MYCISCO(config-if)#mac access-group 1101
>
>Вы же сами пишете - нужен L2 аксесс лист, а на интерфейсе
>вводите команду касаемо L3 аксесс листа.
вот список возможных команд на интерфейсе, какую выбрать? - предложенной Вами нет
MYCISCO(config-if)#?
Interface configuration commands:
access-expression Build a bridge boolean access expression
arp Set arp type (arpa, probe, snap) or timeout
backup Modify backup parameters
bandwidth Set bandwidth informational parameter
bridge-group Transparent bridging interface parameters
carrier-delay Specify delay for interface transitions
cdp CDP interface subcommands
cmns OSI CMNS
custom-queue-list Assign a custom queue list to an interface
default Set a command to its defaults
delay Specify interface throughput delay
description Interface specific description
diffserv diffserv (Provisioning)
duplex Configure duplex operation.
exit Exit from interface configuration mode
fair-queue Enable Fair Queuing on an Interface
full-duplex Configure full-duplex operational mode
half-duplex Configure half-duplex and related commands
help Description of the interactive help system
hold-queue Set hold queue depth
ip Interface Internet Protocol config commands
keepalive Enable keepalive
llc2 LLC2 Interface Subcommands
load-interval Specify interval for load calculation for an interface
logging Configure logging for interface
loopback Configure internal loopback on an interface
mac-address Manually set interface MAC address
max-reserved-bandwidth Maximum Reservable Bandwidth on an Interface
media-type Interface media type
mtu Set the interface Maximum Transmission Unit (MTU)
multilink-group Put interface in a multilink bundle
netbios Use a defined NETBIOS access list or enable name-caching
no Negate a command or set its defaults
ntp Configure NTP
priority-group Assign a priority group to an interface
random-detect Enable Weighted Random Early Detection (WRED) on an Interface
rate-limit Rate Limit
roles Specify roles (by entering roles mode)
service-policy Configure QoS Service Policy
shutdown Shutdown the selected interface
snapshot Configure snapshot support on the interface
snmp Modify SNMP interface parameters
speed Configure speed operation.
standby HSRP interface configuration commands
timeout Define timeout values for this interface
traffic-shape Enable Traffic Shaping on an Interface or Sub-Interface
transmit-interface Assign a transmit interface to a receive-only interface
trunk-group Configure interface to be in a trunk group
tx-ring-limit Configure PA level transmit ring limit
MYCISCO(config-if)#ip ?
Interface IP configuration subcommands:
access-group Specify access control for packets
accounting Enable IP accounting on this interface
address Set the IP address of an interface
authentication authentication subcommands
bandwidth-percent Set EIGRP bandwidth limit
bgp BGP interface commands
broadcast-address Set the broadcast address of an interface
cef Cisco Express Fowarding interface commands
cgmp Enable/disable CGMP
dhcp Configure DHCP parameters for this interface
directed-broadcast Enable forwarding of directed broadcasts
dvmrp DVMRP interface commands
hello-interval Configures IP-EIGRP hello interval
helper-address Specify a destination address for UDP broadcasts
hold-time Configures IP-EIGRP hold time
idle-group Specify interesting packets for idle-timer
igmp IGMP interface commands
irdp ICMP Router Discovery Protocol
load-sharing Style of load sharing
local-proxy-arp Enable local-proxy ARP
mask-reply Enable sending ICMP Mask Reply messages
mrm Configure IP Multicast Routing Monitor tester
mroute-cache Enable switching cache for incoming multicast packets
mtu Set IP Maximum Transmission Unit
multicast IP multicast interface commands
nat NAT interface commands
nbar Network-Based Application Recognition
nhrp NHRP interface subcommands
ospf OSPF interface commands
pim PIM interface commands
policy Enable policy routing
probe Enable HP Probe support
proxy-arp Enable proxy ARP
rarp-server Enable RARP server for static arp entries
redirects Enable sending ICMP Redirect messages
rgmp Enable/disable RGMP
rip Router Information Protocol
route-cache Enable fast-switching cache for outgoing packets
rsvp RSVP interface commands
rtp RTP parameters
sap Session Announcement Protocol interface commands
security DDN IP Security Option
split-horizon Perform split horizon
summary-address Perform address summarization
tcp TCP header compression and other parameters
unnumbered Enable IP processing without an explicit address
unreachables Enable sending ICMP Unreachable messages
urd Configure URL Rendezvousing
verify Enable per packet validation
vrf VPN Routing/Forwarding parameters on the interface
wccp WCCP interface commands