The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

ie ()
  • >> ie (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    ie
    
     - Ethernet device driver
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following line in your kernel configuration file:
    device ie

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_ie_load="YES"
    

    In /boot/device.hints hint.ie.0.at=isa hint.ie.0.port=0x300 hint.ie.0.irq=5 hint.ie.0.maddr=0xd0000  

    HARDWARE

    The driver provides supports the following 8 and 16bit ISA Ethernet cards that are based on the Intel i82586 chip:

     

    DIAGNOSTICS

    "ie%d: unknown board type code %d"
    An i82586 chip was found, but the driver was unable to determine the actual board type during the probe.
    "ie%d: kernel configured maddr %x doesn't match board configured maddr %x"
    The device probe detected a different maddr than the one specified in the kernel configuration file.
    "ie%d: can't find shared memory"
    The device probe could not access the shared memory to determine its size.
    "ie%d: kernel configured msize %d doesn't match board configured msize %d"
    The device probe found a different size for the shared memory than the one specified in the kernel configuration file.
    "ie%d: kernel configured irq %d doesn't match board configured irq %d"
    The device probe detected that the board is configured for a different interrupt than the one specified in the kernel configuration file.
    "ie%d: reset"
    The Intel i82586 had to be reset by the driver.
    "ie%d: transceiver problem"
    The driver has detected a problem with the Ethernet transceiver. This is usually due to a loose or broken transceiver cable when using an external transceiver. When you experience this problem with an on-card transceiver your card may be incorrectly jumpered for to use an external transceiver. Worst case your on-board transceiver may be broken.
    "ie%d: TDR detected an open %d clocks away"
    The driver detected an open circuit in the Ethernet cable. Check your coax cable and terminator resistors.
    "ie%d: TDR detected a short %d clocks away"
    The driver detected a short circuit in the Ethernet cable. Check your coax cable and terminator resistors.
    "ie%d: TDR returned unknown status %x"
    The driver got an unknown status from the card during the Ethernet cable test.
    "ie%d: multicast address setup command failed"
    The card could not be put into multicast mode.
    "ie%d: configure command failed"
    The card refused to respond correctly during configuration.
    "ie%d: individual address setup command failed"
    The programming of the Ethernet (MAC) address failed.

     

    CAVEATS

    The Racal Interlan NI5210 comes in variants with 8 and 16 kbytes of shared memory. It is strongly advisable to use the 16 kbyte variant. You can upgrade your 8 kbyte card to 16 kbyte by adding an additional RAM chip.  

    SEE ALSO

    arp(4), netintro(4), ng_ether4, ifconfig(8)  

    AUTHORS

    An -nosplit The device driver was written by An Garrett A. Wollman , based on code by An William F. Jolitz and Lawrence Berkeley Laboratories. 3C507 support was written by An Charles M. Hannum . This manual page was written by An Wilko C. Bulte .


     

    Index

    NAME
    SYNOPSIS
    HARDWARE
    DIAGNOSTICS
    CAVEATS
    SEE ALSO
    AUTHORS


    Поиск по тексту MAN-ов: 




    Спонсоры:
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2020 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру