The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

mediator (7)
  • >> mediator (7) ( Solaris man: Макропакеты и соглашения )
  •  

    NAME

    mediator - support for HA configurations consisting of two strings of drives 
     
    

    DESCRIPTION

    Beginning with a prior version, Solaris Volume Manager provided support for high-availability (HA) configurations consisting of two hosts that share at least three strings of drives and that run software enabling exclusive access to the data on those drives from one host. (Note: Volume Manager, by itself, does not actually provide a high-availability environment. The diskset feature is an enabler for HA configurations.)

    Volume Manager provides support for a low-end HA solution consisting of two hosts that share only two strings of drives. The hosts in this type of configuration, referred to as mediators, run a special daemon, rpc.metamedd(1M). The mediator hosts take on additional responsibilities to ensure that data is available in the case of host or drive failures.

    In a mediator configuration, two hosts are physically connected to two strings of drives. This configuration can survive the failure of a single host or a single string of drives, without administrative intervention. If both a host and a string of drives fail (multiple failures), the integrity of the data cannot be guaranteed. At this point, administrative intervention is required to make the data accessible.

    The following definitions pertain to a mediator configuration:

    diskset

    A set of drives containing metadevices and hot spares that can be shared exclusively (but not concurrently) by two hosts.

    Volume Manager state database

    A replicated database that stores metadevice configuration and state information.

    mediator host

    A host that runs the rpc.metamedd(1M) daemon and that has been added to a diskset. The mediator host participates in checking the state database and the mediator quorum.

    mediator quorum

    The condition achieved when the number of accessible mediator hosts is equal to half+1 the total number of configured mediator hosts. Because it is expected that there will be two mediator hosts, this number will normally be 2 ([(2/2) + 1] = 2.)

    replica

    A single copy of the Volume Manager metadevice state database.

    replica quorum

    The condition achieved when the number of accessible replicas is equal to half+1 the total number of configured replicas. For example, if a system is configured with ten replicas, the quorum is met when six are accessible ([(10/2) + 1 = 6]).

    A mediator host running the rpc.metamedd(1M) daemon keeps track of replica updates. As long as the following conditions are met, access to data occurs without any administrative intervention:

    o The replica quorum is not met.
    o Half of the replicas is still accessible.
    o The mediator quorum is met.

    The following conditions describe the operation of mediator hosts:

    1.
    If the replica quorum is met, access to the diskset is granted. At this point no mediator host is involved.
    2.
    If the replica quorum is not met, half of the replicas is accessible, the mediator quorum is met, and the replica and mediator data match, access to the diskset is granted. The mediator host contributes the deciding vote.
    3.
    If the replica quorum is not met, half of the replicas is accessible, the mediator quorum is not met, half of the mediator hosts is accessible, and the replica and mediator data match, the system prompts you to grant or deny access to the diskset.
    4.
    If the replica quorum is not met, half of the replicas is accessible, the mediator quorum is met, and the replica and mediator data do not match, access to the diskset is read-only. You can delete replicas, release the diskset, and retake the diskset to gain read-write access to the data in the diskset.
    5.

     In all other cases, the diskset access is read-only. You can delete replicas, release the diskset, and retake the diskset to gain read-write access to the data in the diskset.

    The metaset(1M) command administers disksets and mediator hosts. The following options to the metaset command pertain only to administering mediator hosts.

    -a -m mediator_host_list

    Adds mediator hosts to the named set. A mediator_host_list is the nodename of the mediator host to be added and up to 2 other aliases for the mediator host. The nodename and aliases for each mediator host are separated by commas. Up to 3 mediator hosts can be specified for the named diskset.

    -d -m mediator_host_list

    Deletes mediator hosts from the named diskset. Mediator hosts are deleted from the diskset by specifying the nodename of mediator host to delete.

    -q

    Displays an enumerated list of tags pertaining to ``tagged data'' that may be encountered during a take of the ownership of a diskset.

    -t [-f] -y

    Takes ownership of a diskset safely, unless -f is used, in which case the take is unconditional. If metaset finds that another host owns the set, this host will not be allowed to take ownership of the set. If the set is not owned by any other host, all the disks within the set will be owned by the host on which metaset was executed. The metadevice state database is read in and the shared metadevices contained in the set become accessible. The -t option will take a diskset that has stale databases. When the databases are stale, metaset will exit with code 66, and a message will be printed. At that point, the only operations permitted are the addition and deletion of replicas. Once the addition or deletion of the replicas has been completed, the diskset should be released and retaken to gain full access to the data. If mediator hosts have been configured, some additional exit codes are possible. If half of the replicas and half of the mediator hosts are operating properly, the take will exit with code 3. At this point, you can add or delete replicas, or use the -y option on a subsequent take. If the take operation encounters ``tagged data,'' the take operation will exit with code 2. You can then run the metaset command with the -q option to see an enumerated list of tags.

    -t [-f] -u tagnumber

    Once a tag has been selected, a subsequent take with -u tagnumber can be executed to select the data associated with the given tagnumber.

     

    SEE ALSO

    metaset(1M), md(7D), rpc.metamedd(1M), rpc.metad(1M)

    Sun Cluster documentation, Solaris Volume Manager Administration Guide  

    NOTES

    Diskset administration, including the addition and deletion of hosts and drives, requires all hosts in the set to be accessible from the network.


     

    Index

    NAME
    DESCRIPTION
    SEE ALSO
    NOTES


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру