The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

ng_ether (4)
  • >> ng_ether (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    ng_ether
    
     - Ethernet netgraph node type
    
     
    

    SYNOPSIS

       #include <netgraph/ng_ether.h>
     

    DESCRIPTION

    The ether netgraph node type allows Ethernet interfaces to interact with the netgraph(4) networking subsystem. Once the module is loaded into the kernel, a node is automatically created for each Ethernet interface in the system. Each node will attempt to name itself with the same name as the associated interface.

    Three hooks are supported: lower , upper and orphans The hook name divert may be used as an alias for lower and is provided for backward compatibility. In reality, the two names represent the same hook.

    The lower hook is a connection to the raw Ethernet device. When connected, all incoming packets are forwarded to this hook, instead of being passed to the kernel for upper layer processing. Writing to this hook results in a raw Ethernet frame being transmitted by the device. Normal outgoing packets are not affected by lower being connected.

    The upper hook is a connection to the upper protocol layers. When connected, all outgoing packets are forwarded to this hook, instead of being transmitted by the device. Writing to this hook results in a raw Ethernet frame being received by the kernel just as if it had come in over the wire. Normal incoming packets are not affected by upper being connected.

    The orphans hook is equivalent to lower except that only unrecognized packets (that would otherwise be discarded) are written to the hook, while other normal incoming traffic is unaffected. Unrecognized packets written to upper will be forwarded back out to orphans if connected.

    In all cases, frames are raw Ethernet frames with the standard 14 byte Ethernet header (but no checksum).

    When no hooks are connected, upper and lower are in effect connected together, so that packets flow normally upwards and downwards.  

    HOOKS

    This node type supports the following hooks:

    lower
    Connection to the lower device link layer.
    upper
    Connection to the upper protocol layers.
    orphans
    Like lower but only receives unrecognized packets.

     

    CONTROL MESSAGES

    This node type supports the generic control messages, plus the following:

    NGM_ETHER_GET_IFNAME (getifname )
    Returns the name of the associated interface as a NUL -terminated ASCII string. Normally this is the same as the name of the node.
    NGM_ETHER_GET_IFINDEX (getifindex )
    Returns the global index of the associated interface as a 32 bit integer.
    NGM_ETHER_GET_ENADDR (getenaddr )
    Returns the device's unique six byte Ethernet address.
    NGM_ETHER_SET_ENADDR (setenaddr )
    Sets the device's unique six byte Ethernet address. This control message is equivalent to using the SIOCSIFLLADDR ioctl(2) system call.
    NGM_ETHER_SET_PROMISC (setpromisc )
    Enable or disable promiscuous mode. This message includes a single 32 bit integer flag that enables or disables promiscuous mode on the interface. Any non-zero value enables promiscuous mode.
    NGM_ETHER_GET_PROMISC (getpromisc )
    Get the current value of the node's promiscuous flag. The returned value is always either one or zero. Note that this flag reflects the node's own promiscuous setting and does not necessarily reflect the promiscuous state of the actual interface, which can be affected by other means (e.g., bpf(4)).
    NGM_ETHER_SET_AUTOSRC (setautosrc )
    Sets the automatic source address override flag. This message includes a single 32 bit integer flag that causes all outgoing packets to have their source Ethernet address field overwritten with the device's unique Ethernet address. If this flag is set to zero, the source address in outgoing packets is not modified. The default setting for this flag is disabled.
    NGM_ETHER_GET_AUTOSRC (getautosrc )
    Get the current value of the node's source address override flag. The returned value is always either one or zero.
    NGM_ETHER_ADD_MULTI (addmulti )
    Join Ethernet multicast group. This control message is equivalent to using the SIOCADDMULTI ioctl(2) system call.
    NGM_ETHER_DEL_MULTI (delmulti )
    Leave Ethernet multicast group. This control message is equivalent to using the SIOCDELMULTI ioctl(2) system call.
    NGM_ETHER_DETACH (detach )
    Detach from underlying Ethernet interface and shut down node.

     

    SHUTDOWN

    Upon receipt of the NGM_SHUTDOWN control message, all hooks are disconnected, promiscuous mode is disabled, and the source address override flag is re-enabled, but the node is not removed. Node can be shut down only using NGM_ETHER_DETACH control message. If the interface itself is detached (e.g., because of PC Card removal), the node disappears as well.  

    EXAMPLES

    This command dumps all unrecognized packets received by the ``fxp0 '' interface to standard output decoded in hex and ASCII

    "nghook -a fxp0: orphans"

    This command sends the contents of sample.pkt out the interface ``fxp0 ''

    "cat sample.pkt | nghook fxp0: orphans"

    These commands insert an ng_tee4 node between the lower and upper protocol layers, which can be used for tracing packet flow, statistics, etc.:

    ngctl mkpeer fxp0: tee lower right
    ngctl connect fxp0: lower upper left
    
     

    SEE ALSO

    arp(4), netgraph(4), netintro(4), ifconfig(8), ngctl(8), nghook(8)  

    AUTHORS

    An Julian Elischer Aq julian@FreeBSD.org An Archie Cobbs Aq archie@FreeBSD.org  

    BUGS

    The automatic KLD module loading mechanism that works for most other Netgraph node types does not work for the ether node type, because ether nodes are not created on demand; instead, they are created when Ethernet interfaces are attached or when the KLD is first loaded. Therefore, if the KLD is not statically compiled into the kernel, it is necessary to load the KLD manually in order to bring the ether nodes into existence.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HOOKS
    CONTROL MESSAGES
    SHUTDOWN
    EXAMPLES
    SEE ALSO
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру