The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

форумы  помощь  поиск  регистрация  майллист  вход/выход  слежка  RSS
"Freeradius 2.1.6 не коннектится к базе PostgreSQL"
Вариант для распечатки  
Пред. тема | След. тема 
Форумы OpenNET: Виртуальная конференция (Public)
Изначальное сообщение [ Отслеживать ]

"Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 12:03 
Проблема в том, что Radius не хочет работать с PostgreSQL. Т.е. если аккаунт завести в users, radtest выполняется без проблем, как только тестирую аккаунт из БД - reject. Есть подозрение, что radius-сервер не грузит драйвер для PostgreSQL, но как исправить это - я не пойму. Пожалуйста, помогите найти решение. Вот конфиг и логи:

raduisd -Xx:

Sat Jul 18 11:05:32 2009 : Info: FreeRADIUS Version 2.1.6, for host i386-portbld-freebsd7.0, built on Jul 18 2009 at 09:39:08
Sat Jul 18 11:05:32 2009 : Info: Copyright (C) 1999-2009 The FreeRADIUS server project and contributors.
Sat Jul 18 11:05:32 2009 : Info: There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A
Sat Jul 18 11:05:32 2009 : Info: PARTICULAR PURPOSE.
Sat Jul 18 11:05:32 2009 : Info: You may redistribute copies of FreeRADIUS under the terms of the
Sat Jul 18 11:05:32 2009 : Info: GNU General Public License v2.
Sat Jul 18 11:05:32 2009 : Info: Starting - reading configuration files ...
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/radiusd.conf
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/proxy.conf
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/clients.conf
Sat Jul 18 11:05:32 2009 : Debug: including files in directory /usr/local/etc/raddb/modules/
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/wimax
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/always
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/attr_filter
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/attr_rewrite
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/chap
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/checkval
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/counter
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/detail
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/detail.example.com
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/detail.log
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/digest
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/echo
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/etc_group
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/exec
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/expiration
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/expr
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/files
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/inner-eap
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/ippool
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/krb5
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/ldap
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/linelog
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/logintime
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/mac2ip
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/mac2vlan
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/mschap
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/otp
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/pam
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/pap
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/passwd
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/perl
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/policy
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/preprocess
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/radutmp
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/realm
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/smbpasswd
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/smsotp
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/sql_log
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/sqlcounter_expire_on_login
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/sradutmp
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/unix
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/modules/acct_unique
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/eap.conf
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/sql.conf
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/sql/postgresql/dialup.conf
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/policy.conf
Sat Jul 18 11:05:32 2009 : Debug: including files in directory /usr/local/etc/raddb/sites-enabled/
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/sites-enabled/default
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/sites-enabled/inner-tunnel
Sat Jul 18 11:05:32 2009 : Debug: including configuration file /usr/local/etc/raddb/sites-enabled/control-socket
Sat Jul 18 11:05:32 2009 : Debug: group = freeradius
Sat Jul 18 11:05:32 2009 : Debug: user = freeradius
Sat Jul 18 11:05:32 2009 : Debug: including dictionary file /usr/local/etc/raddb/dictionary
Sat Jul 18 11:05:32 2009 : Debug: main {
Sat Jul 18 11:05:32 2009 : Debug:     prefix = "/usr/local/"
Sat Jul 18 11:05:32 2009 : Debug:     localstatedir = "/var"
Sat Jul 18 11:05:32 2009 : Debug:     logdir = "/var/log"
Sat Jul 18 11:05:32 2009 : Debug:     libdir = "/usr/local/lib/freeradius-2.1.6"
Sat Jul 18 11:05:32 2009 : Debug:     radacctdir = "/var/log/radacct"
Sat Jul 18 11:05:32 2009 : Debug:     hostname_lookups = no
Sat Jul 18 11:05:32 2009 : Debug:     max_request_time = 30
Sat Jul 18 11:05:32 2009 : Debug:     cleanup_delay = 5
Sat Jul 18 11:05:32 2009 : Debug:     max_requests = 1024
Sat Jul 18 11:05:32 2009 : Debug:     allow_core_dumps = no
Sat Jul 18 11:05:32 2009 : Debug:     pidfile = "/var/run/radiusd/radiusd.pid"
Sat Jul 18 11:05:32 2009 : Debug:     checkrad = "/usr/local/sbin/checkrad"
Sat Jul 18 11:05:32 2009 : Debug:     debug_level = 0
Sat Jul 18 11:05:32 2009 : Debug:     proxy_requests = yes
Sat Jul 18 11:05:32 2009 : Debug:  log {
Sat Jul 18 11:05:32 2009 : Debug:     stripped_names = no
Sat Jul 18 11:05:32 2009 : Debug:     auth = no
Sat Jul 18 11:05:32 2009 : Debug:     auth_badpass = no
Sat Jul 18 11:05:32 2009 : Debug:     auth_goodpass = no
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug:  security {
Sat Jul 18 11:05:32 2009 : Debug:     max_attributes = 200
Sat Jul 18 11:05:32 2009 : Debug:     reject_delay = 1
Sat Jul 18 11:05:32 2009 : Debug:     status_server = yes
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug: }
Sat Jul 18 11:05:32 2009 : Debug: radiusd: #### Loading Realms and Home Servers ####
Sat Jul 18 11:05:32 2009 : Debug:  proxy server {
Sat Jul 18 11:05:32 2009 : Debug:     retry_delay = 5
Sat Jul 18 11:05:32 2009 : Debug:     retry_count = 3
Sat Jul 18 11:05:32 2009 : Debug:     default_fallback = no
Sat Jul 18 11:05:32 2009 : Debug:     dead_time = 120
Sat Jul 18 11:05:32 2009 : Debug:     wake_all_if_all_dead = no
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug:  home_server localhost {
Sat Jul 18 11:05:32 2009 : Debug:     ipaddr = 127.0.0.1
Sat Jul 18 11:05:32 2009 : Debug:     port = 1812
Sat Jul 18 11:05:32 2009 : Debug:     type = "auth"
Sat Jul 18 11:05:32 2009 : Debug:     secret = "testing123"
Sat Jul 18 11:05:32 2009 : Debug:     response_window = 20
Sat Jul 18 11:05:32 2009 : Debug:     max_outstanding = 65536
Sat Jul 18 11:05:32 2009 : Debug:     require_message_authenticator = no
Sat Jul 18 11:05:32 2009 : Debug:     zombie_period = 40
Sat Jul 18 11:05:32 2009 : Debug:     status_check = "status-server"
Sat Jul 18 11:05:32 2009 : Debug:     ping_interval = 30
Sat Jul 18 11:05:32 2009 : Debug:     check_interval = 30
Sat Jul 18 11:05:32 2009 : Debug:     num_answers_to_alive = 3
Sat Jul 18 11:05:32 2009 : Debug:     num_pings_to_alive = 3
Sat Jul 18 11:05:32 2009 : Debug:     revive_interval = 120
Sat Jul 18 11:05:32 2009 : Debug:     status_check_timeout = 4
Sat Jul 18 11:05:32 2009 : Debug:     irt = 2
Sat Jul 18 11:05:32 2009 : Debug:     mrt = 16
Sat Jul 18 11:05:32 2009 : Debug:     mrc = 5
Sat Jul 18 11:05:32 2009 : Debug:     mrd = 30
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug:  home_server_pool my_auth_failover {
Sat Jul 18 11:05:32 2009 : Debug:     type = fail-over
Sat Jul 18 11:05:32 2009 : Debug:     home_server = localhost
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug:  realm example.com {
Sat Jul 18 11:05:32 2009 : Debug:     auth_pool = my_auth_failover
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug:  realm LOCAL {
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug: radiusd: #### Loading Clients ####
Sat Jul 18 11:05:32 2009 : Debug:  client localhost {
Sat Jul 18 11:05:32 2009 : Debug:     ipaddr = 127.0.0.1
Sat Jul 18 11:05:32 2009 : Debug:     require_message_authenticator = no
Sat Jul 18 11:05:32 2009 : Debug:     secret = "test"
Sat Jul 18 11:05:32 2009 : Debug:     nastype = "other"
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug: radiusd: #### Instantiating modules ####
Sat Jul 18 11:05:32 2009 : Debug:  instantiate {
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_expr, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_expr
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating expr
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_expiration, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_expiration
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating expiration
Sat Jul 18 11:05:32 2009 : Debug:   expiration {
Sat Jul 18 11:05:32 2009 : Debug:     reply-message = "Password Has Expired  "
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_logintime, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_logintime
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating logintime
Sat Jul 18 11:05:32 2009 : Debug:   logintime {
Sat Jul 18 11:05:32 2009 : Debug:     reply-message = "You are calling outside your allowed timespan  "
Sat Jul 18 11:05:32 2009 : Debug:     minimum-timeout = 60
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug: radiusd: #### Loading Virtual Servers ####
Sat Jul 18 11:05:32 2009 : Debug: server inner-tunnel {
Sat Jul 18 11:05:32 2009 : Debug:  modules {
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking authenticate {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_pap, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_pap
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating pap
Sat Jul 18 11:05:32 2009 : Debug:   pap {
Sat Jul 18 11:05:32 2009 : Debug:     encryption_scheme = "auto"
Sat Jul 18 11:05:32 2009 : Debug:     auto_header = no
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_chap, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_chap
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating chap
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_mschap, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_mschap
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating mschap
Sat Jul 18 11:05:32 2009 : Debug:   mschap {
Sat Jul 18 11:05:32 2009 : Debug:     use_mppe = yes
Sat Jul 18 11:05:32 2009 : Debug:     require_encryption = no
Sat Jul 18 11:05:32 2009 : Debug:     require_strong = no
Sat Jul 18 11:05:32 2009 : Debug:     with_ntdomain_hack = no
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_unix, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_unix
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating unix
Sat Jul 18 11:05:32 2009 : Debug:   unix {
Sat Jul 18 11:05:32 2009 : Debug:     radwtmp = "/var/log/radwtmp"
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_eap, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_eap
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap
Sat Jul 18 11:05:32 2009 : Debug:   eap {
Sat Jul 18 11:05:32 2009 : Debug:     default_eap_type = "md5"
Sat Jul 18 11:05:32 2009 : Debug:     timer_expire = 60
Sat Jul 18 11:05:32 2009 : Debug:     ignore_unknown_eap_types = no
Sat Jul 18 11:05:32 2009 : Debug:     cisco_accounting_username_bug = no
Sat Jul 18 11:05:32 2009 : Debug:     max_sessions = 2048
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to sub-module rlm_eap_md5
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap-md5
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to sub-module rlm_eap_leap
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap-leap
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to sub-module rlm_eap_gtc
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap-gtc
Sat Jul 18 11:05:32 2009 : Debug:    gtc {
Sat Jul 18 11:05:32 2009 : Debug:     challenge = "Password: "
Sat Jul 18 11:05:32 2009 : Debug:     auth_type = "PAP"
Sat Jul 18 11:05:32 2009 : Debug:    }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to sub-module rlm_eap_tls
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap-tls
Sat Jul 18 11:05:32 2009 : Debug:    tls {
Sat Jul 18 11:05:32 2009 : Debug:     rsa_key_exchange = no
Sat Jul 18 11:05:32 2009 : Debug:     dh_key_exchange = yes
Sat Jul 18 11:05:32 2009 : Debug:     rsa_key_length = 512
Sat Jul 18 11:05:32 2009 : Debug:     dh_key_length = 512
Sat Jul 18 11:05:32 2009 : Debug:     verify_depth = 0
Sat Jul 18 11:05:32 2009 : Debug:     pem_file_type = yes
Sat Jul 18 11:05:32 2009 : Debug:     private_key_file = "/usr/local/etc/raddb/certs/server.pem"
Sat Jul 18 11:05:32 2009 : Debug:     certificate_file = "/usr/local/etc/raddb/certs/server.pem"
Sat Jul 18 11:05:32 2009 : Debug:     CA_file = "/usr/local/etc/raddb/certs/ca.pem"
Sat Jul 18 11:05:32 2009 : Debug:     private_key_password = "whatever"
Sat Jul 18 11:05:32 2009 : Debug:     dh_file = "/usr/local/etc/raddb/certs/dh"
Sat Jul 18 11:05:32 2009 : Debug:     random_file = "/usr/local/etc/raddb/certs/random"
Sat Jul 18 11:05:32 2009 : Debug:     fragment_size = 1024
Sat Jul 18 11:05:32 2009 : Debug:     include_length = yes
Sat Jul 18 11:05:32 2009 : Debug:     check_crl = no
Sat Jul 18 11:05:32 2009 : Debug:     cipher_list = "DEFAULT"
Sat Jul 18 11:05:32 2009 : Debug:     make_cert_command = "/usr/local/etc/raddb/certs/bootstrap"
Sat Jul 18 11:05:32 2009 : Debug:     cache {
Sat Jul 18 11:05:32 2009 : Debug:     enable = no
Sat Jul 18 11:05:32 2009 : Debug:     lifetime = 24
Sat Jul 18 11:05:32 2009 : Debug:     max_entries = 255
Sat Jul 18 11:05:32 2009 : Debug:     }
Sat Jul 18 11:05:32 2009 : Debug:    }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to sub-module rlm_eap_ttls
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap-ttls
Sat Jul 18 11:05:32 2009 : Debug:    ttls {
Sat Jul 18 11:05:32 2009 : Debug:     default_eap_type = "md5"
Sat Jul 18 11:05:32 2009 : Debug:     copy_request_to_tunnel = no
Sat Jul 18 11:05:32 2009 : Debug:     use_tunneled_reply = no
Sat Jul 18 11:05:32 2009 : Debug:     virtual_server = "inner-tunnel"
Sat Jul 18 11:05:32 2009 : Debug:     include_length = yes
Sat Jul 18 11:05:32 2009 : Debug:    }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to sub-module rlm_eap_peap
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap-peap
Sat Jul 18 11:05:32 2009 : Debug:    peap {
Sat Jul 18 11:05:32 2009 : Debug:     default_eap_type = "mschapv2"
Sat Jul 18 11:05:32 2009 : Debug:     copy_request_to_tunnel = no
Sat Jul 18 11:05:32 2009 : Debug:     use_tunneled_reply = no
Sat Jul 18 11:05:32 2009 : Debug:     proxy_tunneled_request_as_eap = yes
Sat Jul 18 11:05:32 2009 : Debug:     virtual_server = "inner-tunnel"
Sat Jul 18 11:05:32 2009 : Debug:    }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to sub-module rlm_eap_mschapv2
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating eap-mschapv2
Sat Jul 18 11:05:32 2009 : Debug:    mschapv2 {
Sat Jul 18 11:05:32 2009 : Debug:     with_ntdomain_hack = no
Sat Jul 18 11:05:32 2009 : Debug:    }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking authorize {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_realm, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_realm
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating suffix
Sat Jul 18 11:05:32 2009 : Debug:   realm suffix {
Sat Jul 18 11:05:32 2009 : Debug:     format = "suffix"
Sat Jul 18 11:05:32 2009 : Debug:     delimiter = "@"
Sat Jul 18 11:05:32 2009 : Debug:     ignore_default = no
Sat Jul 18 11:05:32 2009 : Debug:     ignore_null = no
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_files, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_files
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating files
Sat Jul 18 11:05:32 2009 : Debug:   files {
Sat Jul 18 11:05:32 2009 : Debug:     usersfile = "/usr/local/etc/raddb/users"
Sat Jul 18 11:05:32 2009 : Debug:     acctusersfile = "/usr/local/etc/raddb/acct_users"
Sat Jul 18 11:05:32 2009 : Debug:     preproxy_usersfile = "/usr/local/etc/raddb/preproxy_users"
Sat Jul 18 11:05:32 2009 : Debug:     compat = "no"
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking session {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_radutmp, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_radutmp
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating radutmp
Sat Jul 18 11:05:32 2009 : Debug:   radutmp {
Sat Jul 18 11:05:32 2009 : Debug:     filename = "/var/log/radutmp"
Sat Jul 18 11:05:32 2009 : Debug:     username = "%{User-Name}"
Sat Jul 18 11:05:32 2009 : Debug:     case_sensitive = yes
Sat Jul 18 11:05:32 2009 : Debug:     check_with_nas = yes
Sat Jul 18 11:05:32 2009 : Debug:     perm = 384
Sat Jul 18 11:05:32 2009 : Debug:     callerid = yes
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking post-proxy {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking post-auth {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_attr_filter, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_attr_filter
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating attr_filter.access_reject
Sat Jul 18 11:05:32 2009 : Debug:   attr_filter attr_filter.access_reject {
Sat Jul 18 11:05:32 2009 : Debug:     attrsfile = "/usr/local/etc/raddb/attrs.access_reject"
Sat Jul 18 11:05:32 2009 : Debug:     key = "%{User-Name}"
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  } # modules
Sat Jul 18 11:05:32 2009 : Debug: } # server
Sat Jul 18 11:05:32 2009 : Debug: server {
Sat Jul 18 11:05:32 2009 : Debug:  modules {
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking authenticate {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking authorize {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_preprocess, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_preprocess
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating preprocess
Sat Jul 18 11:05:32 2009 : Debug:   preprocess {
Sat Jul 18 11:05:32 2009 : Debug:     huntgroups = "/usr/local/etc/raddb/huntgroups"
Sat Jul 18 11:05:32 2009 : Debug:     hints = "/usr/local/etc/raddb/hints"
Sat Jul 18 11:05:32 2009 : Debug:     with_ascend_hack = no
Sat Jul 18 11:05:32 2009 : Debug:     ascend_channels_per_line = 23
Sat Jul 18 11:05:32 2009 : Debug:     with_ntdomain_hack = no
Sat Jul 18 11:05:32 2009 : Debug:     with_specialix_jetstream_hack = no
Sat Jul 18 11:05:32 2009 : Debug:     with_cisco_vsa_hack = no
Sat Jul 18 11:05:32 2009 : Debug:     with_alvarion_vsa_hack = no
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking preacct {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_acct_unique, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_acct_unique
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating acct_unique
Sat Jul 18 11:05:32 2009 : Debug:   acct_unique {
Sat Jul 18 11:05:32 2009 : Debug:     key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port"
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking accounting {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_detail, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_detail
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating detail
Sat Jul 18 11:05:32 2009 : Debug:   detail {
Sat Jul 18 11:05:32 2009 : Debug:     detailfile = "/var/log/radacct/%{Client-IP-Address}/detail-%Y%m%d"
Sat Jul 18 11:05:32 2009 : Debug:     header = "%t"
Sat Jul 18 11:05:32 2009 : Debug:     detailperm = 384
Sat Jul 18 11:05:32 2009 : Debug:     dirperm = 493
Sat Jul 18 11:05:32 2009 : Debug:     locking = no
Sat Jul 18 11:05:32 2009 : Debug:     log_packet_header = no
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating attr_filter.accounting_response
Sat Jul 18 11:05:32 2009 : Debug:   attr_filter attr_filter.accounting_response {
Sat Jul 18 11:05:32 2009 : Debug:     attrsfile = "/usr/local/etc/raddb/attrs.accounting_response"
Sat Jul 18 11:05:32 2009 : Debug:     key = "%{User-Name}"
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking session {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking post-proxy {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:  Module: Checking post-auth {...} for more modules to load
Sat Jul 18 11:05:32 2009 : Debug:     (Loaded rlm_exec, checking if it's valid)
Sat Jul 18 11:05:32 2009 : Debug:  Module: Linked to module rlm_exec
Sat Jul 18 11:05:32 2009 : Debug:  Module: Instantiating exec
Sat Jul 18 11:05:32 2009 : Debug:   exec {
Sat Jul 18 11:05:32 2009 : Debug:     wait = no
Sat Jul 18 11:05:32 2009 : Debug:     input_pairs = "request"
Sat Jul 18 11:05:32 2009 : Debug:     shell_escape = yes
Sat Jul 18 11:05:32 2009 : Debug:   }
Sat Jul 18 11:05:32 2009 : Debug:  } # modules
Sat Jul 18 11:05:32 2009 : Debug: } # server
Sat Jul 18 11:05:32 2009 : Debug: radiusd: #### Opening IP addresses and Ports ####
Sat Jul 18 11:05:32 2009 : Debug: listen {
Sat Jul 18 11:05:32 2009 : Debug:     type = "auth"
Sat Jul 18 11:05:32 2009 : Debug:     ipaddr = *
Sat Jul 18 11:05:32 2009 : Debug:     port = 1812
Sat Jul 18 11:05:32 2009 : Debug: }
Sat Jul 18 11:05:32 2009 : Debug: listen {
Sat Jul 18 11:05:32 2009 : Debug:     type = "acct"
Sat Jul 18 11:05:32 2009 : Debug:     ipaddr = *
Sat Jul 18 11:05:32 2009 : Debug:     port = 0
Sat Jul 18 11:05:32 2009 : Debug: }
Sat Jul 18 11:05:32 2009 : Debug: listen {
Sat Jul 18 11:05:32 2009 : Debug:     type = "control"
Sat Jul 18 11:05:32 2009 : Debug:  listen {
Sat Jul 18 11:05:32 2009 : Debug:     socket = "/var/run/radiusd/radiusd.sock"
Sat Jul 18 11:05:32 2009 : Debug:  }
Sat Jul 18 11:05:32 2009 : Debug: }
Sat Jul 18 11:05:32 2009 : Debug: Listening on authentication address * port 1812
Sat Jul 18 11:05:32 2009 : Debug: Listening on accounting address * port 1813
Sat Jul 18 11:05:32 2009 : Debug: Listening on command file /var/run/radiusd/radiusd.sock
Sat Jul 18 11:05:32 2009 : Debug: Listening on proxy address * port 1814
Sat Jul 18 11:05:32 2009 : Debug: Ready to process requests.

Высказать мнение | Ответить | Правка | Cообщить модератору

 Оглавление

Сообщения по теме [Сортировка по времени | RSS]


1. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 12:04 
radiud.conf:
# -*- text -*-
##
## radiusd.conf    -- FreeRADIUS server configuration file.
##
##    http://www.freeradius.org/
##    $Id$
##

######################################################################
#
#    Read "man radiusd" before editing this file.  See the section
#    titled DEBUGGING.  It outlines a method where you can quickly
#    obtain the configuration you want, without running into
#    trouble.
#
#    Run the server in debugging mode, and READ the output.
#
#        $ radiusd -X
#
#    We cannot emphasize this point strongly enough.  The vast
#    majority of problems can be solved by carefully reading the
#    debugging output, which includes warnings about common issues,
#    and suggestions for how they may be fixed.
#
#    There may be a lot of output, but look carefully for words like:
#    "warning", "error", "reject", or "failure".  The messages there
#    will usually be enough to guide you to a solution.
#
#    If you are going to ask a question on the mailing list, then
#    explain what you are trying to do, and include the output from
#    debugging mode (radiusd -X).  Failure to do so means that all
#    of the responses to your question will be people telling you
#    to "post the output of radiusd -X".

######################################################################
#
#      The location of other config files and logfiles are declared
#      in this file.
#
#      Also general configuration for modules can be done in this
#      file, it is exported through the API to modules that ask for
#      it.
#
#    See "man radiusd.conf" for documentation on the format of this
#    file.  Note that the individual configuration items are NOT
#    documented in that "man" page.  They are only documented here,
#    in the comments.
#
#    As of 2.0.0, FreeRADIUS supports a simple processing language
#    in the "authorize", "authenticate", "accounting", etc. sections.
#    See "man unlang" for details.
#

prefix = /usr/local/
exec_prefix = ${prefix}
sysconfdir = ${prefix}/etc
localstatedir = /var
sbindir = ${exec_prefix}/sbin
logdir = /var/log
raddbdir = ${sysconfdir}/raddb
radacctdir = ${logdir}/radacct

#
#  name of the running server.  See also the "-n" command-line option.
name = radiusd

#  Location of config and logfiles.
confdir = ${raddbdir}
run_dir = ${localstatedir}/run/${name}

# Should likely be ${localstatedir}/lib/radiusd
db_dir = ${raddbdir}

#
# libdir: Where to find the rlm_* modules.
#
#   This should be automatically set at configuration time.
#
#   If the server builds and installs, but fails at execution time
#   with an 'undefined symbol' error, then you can use the libdir
#   directive to work around the problem.
#
#   The cause is usually that a library has been installed on your
#   system in a place where the dynamic linker CANNOT find it.  When
#   executing as root (or another user), your personal environment MAY
#   be set up to allow the dynamic linker to find the library.  When
#   executing as a daemon, FreeRADIUS MAY NOT have the same
#   personalized configuration.
#
#   To work around the problem, find out which library contains that symbol,
#   and add the directory containing that library to the end of 'libdir',
#   with a colon separating the directory names.  NO spaces are allowed.
#
#   e.g. libdir = /usr/local/lib:/opt/package/lib
#
#   You can also try setting the LD_LIBRARY_PATH environment variable
#   in a script which starts the server.
#
#   If that does not work, then you can re-configure and re-build the
#   server to NOT use shared libraries, via:
#
#    ./configure --disable-shared
#    make
#    make install
#
libdir = /usr/local/lib/freeradius-2.1.6

#  pidfile: Where to place the PID of the RADIUS server.
#
#  The server may be signalled while it's running by using this
#  file.
#
#  This file is written when ONLY running in daemon mode.
#
#  e.g.:  kill -HUP `cat /var/run/radiusd/radiusd.pid`
#
pidfile = ${run_dir}/${name}.pid

#  chroot: directory where the server does "chroot".
#
#  The chroot is done very early in the process of starting the server.
#  After the chroot has been performed it switches to the "user" listed
#  below (which MUST be specified).  If "group" is specified, it switchs
#  to that group, too.  Any other groups listed for the specified "user"
#  in "/etc/group" are also added as part of this process.
#
#  The current working directory (chdir / cd) is left *outside* of the
#  chroot until all of the modules have been initialized.  This allows
#  the "raddb" directory to be left outside of the chroot.  Once the
#  modules have been initialized, it does a "chdir" to ${logdir}.  This
#  means that it should be impossible to break out of the chroot.
#
#  If you are worried about security issues related to this use of chdir,
#  then simply ensure that the "raddb" directory is inside of the chroot,
#  end be sure to do "cd raddb" BEFORE starting the server.
#
#  If the server is statically linked, then the only files that have
#  to exist in the chroot are ${run_dir} and ${logdir}.  If you do the
#  "cd raddb" as discussed above, then the "raddb" directory has to be
#  inside of the chroot directory, too.
#
#chroot = /path/to/chroot/directory

# user/group: The name (or #number) of the user/group to run radiusd as.
#
#   If these are commented out, the server will run as the user/group
#   that started it.  In order to change to a different user/group, you
#   MUST be root ( or have root privleges ) to start the server.
#
#   We STRONGLY recommend that you run the server with as few permissions
#   as possible.  That is, if you're not using shadow passwords, the
#   user and group items below should be set to radius'.
#
#  NOTE that some kernels refuse to setgid(group) when the value of
#  (unsigned)group is above 60000; don't use group nobody on these systems!
#
#  On systems with shadow passwords, you might have to set 'group = shadow'
#  for the server to be able to read the shadow password file.  If you can
#  authenticate users while in debug mode, but not in daemon mode, it may be
#  that the debugging mode server is running as a user that can read the
#  shadow info, and the user listed below can not.
#
#  The server will also try to use "initgroups" to read /etc/groups.
#  It will join all groups where "user" is a member.  This can allow
#  for some finer-grained access controls.
#
user = freeradius
group = freeradius

#  max_request_time: The maximum time (in seconds) to handle a request.
#
#  Requests which take more time than this to process may be killed, and
#  a REJECT message is returned.
#
#  WARNING: If you notice that requests take a long time to be handled,
#  then this MAY INDICATE a bug in the server, in one of the modules
#  used to handle a request, OR in your local configuration.
#
#  This problem is most often seen when using an SQL database.  If it takes
#  more than a second or two to receive an answer from the SQL database,
#  then it probably means that you haven't indexed the database.  See your
#  SQL server documentation for more information.
#
#  Useful range of values: 5 to 120
#
max_request_time = 30

#  cleanup_delay: The time to wait (in seconds) before cleaning up
#  a reply which was sent to the NAS.
#
#  The RADIUS request is normally cached internally for a short period
#  of time, after the reply is sent to the NAS.  The reply packet may be
#  lost in the network, and the NAS will not see it.  The NAS will then
#  re-send the request, and the server will respond quickly with the
#  cached reply.
#
#  If this value is set too low, then duplicate requests from the NAS
#  MAY NOT be detected, and will instead be handled as seperate requests.
#
#  If this value is set too high, then the server will cache too many
#  requests, and some new requests may get blocked.  (See 'max_requests'.)
#
#  Useful range of values: 2 to 10
#
cleanup_delay = 5

#  max_requests: The maximum number of requests which the server keeps
#  track of.  This should be 256 multiplied by the number of clients.
#  e.g. With 4 clients, this number should be 1024.
#
#  If this number is too low, then when the server becomes busy,
#  it will not respond to any new requests, until the 'cleanup_delay'
#  time has passed, and it has removed the old requests.
#
#  If this number is set too high, then the server will use a bit more
#  memory for no real benefit.
#
#  If you aren't sure what it should be set to, it's better to set it
#  too high than too low.  Setting it to 1000 per client is probably
#  the highest it should be.
#
#  Useful range of values: 256 to infinity
#
max_requests = 1024

#  listen: Make the server listen on a particular IP address, and send
#  replies out from that address. This directive is most useful for
#  hosts with multiple IP addresses on one interface.
#
#  If you want the server to listen on additional addresses, or on
#  additionnal ports, you can use multiple "listen" sections.
#
#  Each section make the server listen for only one type of packet,
#  therefore authentication and accounting have to be configured in
#  different sections.
#
#  The server ignore all "listen" section if you are using '-i' and '-p'
#  on the command line.
#
listen {
    #  Type of packets to listen for.
    #  Allowed values are:
    #    auth    listen for authentication packets
    #    acct    listen for accounting packets
    #    proxy   IP to use for sending proxied packets
    #    detail  Read from the detail file.  For examples, see
    #               raddb/sites-available/copy-acct-to-home-server
    #    status  listen for Status-Server packets.  For examples,
    #        see raddb/sites-available/status
    #
    type = auth

    #  Note: "type = proxy" lets you control the source IP used for
    #        proxying packets, with some limitations:
    #
    #    * Only ONE proxy listener can be defined.
    #    * A proxy listener CANNOT be used in a virtual server section.
    #    * You should probably set "port = 0".
    #    * Any "clients" configuration will be ignored.

    #  IP address on which to listen.
    #  Allowed values are:
    #    dotted quad (1.2.3.4)
    #       hostname    (radius.example.com)
    #       wildcard    (*)
    ipaddr = *

    #  OR, you can use an IPv6 address, but not both
    #  at the same time.
#    ipv6addr = ::    # any.  ::1 == localhost

    #  Port on which to listen.
    #  Allowed values are:
    #    integer port number (1812)
    #    0 means "use /etc/services for the proper port"
    port = 1812

    #  Some systems support binding to an interface, in addition
    #  to the IP address.  This feature isn't strictly necessary,
    #  but for sites with many IP addresses on one interface,
    #  it's useful to say "listen on all addresses for eth0".
    #
    #  If your system does not support this feature, you will
    #  get an error if you try to use it.
    #
#    interface = eth0

    #  Per-socket lists of clients.  This is a very useful feature.
    #
    #  The name here is a reference to a section elsewhere in
    #  radiusd.conf, or clients.conf.  Having the name as
    #  a reference allows multiple sockets to use the same
    #  set of clients.
    #
    #  If this configuration is used, then the global list of clients
    #  is IGNORED for this "listen" section.  Take care configuring
    #  this feature, to ensure you don't accidentally disable a
    #  client you need.
    #
    #  See clients.conf for the configuration of "per_socket_clients".
    #
#    clients = per_socket_clients
}

#  This second "listen" section is for listening on the accounting
#  port, too.
#
listen {
    ipaddr = *
#    ipv6addr = ::
    port = 0
    type = acct
#    interface = eth0
#    clients = per_socket_clients
}

#  hostname_lookups: Log the names of clients or just their IP addresses
#  e.g., www.freeradius.org (on) or 206.47.27.232 (off).
#
#  The default is 'off' because it would be overall better for the net
#  if people had to knowingly turn this feature on, since enabling it
#  means that each client request will result in AT LEAST one lookup
#  request to the nameserver.   Enabling hostname_lookups will also
#  mean that your server may stop randomly for 30 seconds from time
#  to time, if the DNS requests take too long.
#
#  Turning hostname lookups off also means that the server won't block
#  for 30 seconds, if it sees an IP address which has no name associated
#  with it.
#
#  allowed values: {no, yes}
#
hostname_lookups = no

#  Core dumps are a bad thing.  This should only be set to 'yes'
#  if you're debugging a problem with the server.
#
#  allowed values: {no, yes}
#
allow_core_dumps = no

#  Regular expressions
#
#  These items are set at configure time.  If they're set to "yes",
#  then setting them to "no" turns off regular expression support.
#
#  If they're set to "no" at configure time, then setting them to "yes"
#  WILL NOT WORK.  It will give you an error.
#
regular_expressions    = yes
extended_expressions    = yes

#
#  Logging section.  The various "log_*" configuration items
#  will eventually be moved here.
#
log {
    #
    #  Destination for log messages.  This can be one of:
    #
    #    files - log to "file", as defined below.
    #    syslog - to syslog (see also the "syslog_facility", below.
    #    stdout - standard output
    #    stderr - standard error.
    #
    #  The command-line option "-X" over-rides this option, and forces
    #  logging to go to stdout.
    #
    destination = files

    #
    #  The logging messages for the server are appended to the
    #  tail of this file if destination == "files"
    #
    #  If the server is running in debugging mode, this file is
    #  NOT used.
    #
    file = ${logdir}/radius.log

    #
    #  If this configuration parameter is set, then log messages for
    #  a *request* go to this file, rather than to radius.log.
    #
    #  i.e. This is a log file per request, once the server has accepted
    #  the request as being from a valid client.  Messages that are
    #  not associated with a request still go to radius.log.
    #
    #  Not all log messages in the server core have been updated to use
    #  this new internal API.  As a result, some messages will still
    #  go to radius.log.  Please submit patches to fix this behavior.
    #
    #  The file name is expanded dynamically.  You should ONLY user
    #  server-side attributes for the filename (e.g. things you control).
    #  Using this feature MAY also slow down the server substantially,
    #  especially if you do thinks like SQL calls as part of the
    #  expansion of the filename.
    #
    #  The name of the log file should use attributes that don't change
    #  over the lifetime of a request, such as User-Name,
    #  Virtual-Server or Packet-Src-IP-Address.  Otherwise, the log
    #  messages will be distributed over multiple files.
    #
    #  Logging can be enabled for an individual request by a special
    #  dynamic expansion macro:  %{debug: 1}, where the debug level
    #  for this request is set to '1' (or 2, 3, etc.).  e.g.
    #
    #    ...
    #    update control {
    #           Tmp-String-0 = "%{debug:1}"
    #    }
    #    ...
    #
    #  The attribute that the value is assigned to is unimportant,
    #  and should be a "throw-away" attribute with no side effects.
    #
    #requests = ${logdir}/radiusd-%{%{Virtual-Server}:-DEFAULT}-%Y%m%d.log

    #
    #  Which syslog facility to use, if ${destination} == "syslog"
    #
    #  The exact values permitted here are OS-dependent.  You probably
    #  don't want to change this.
    #
    syslog_facility = daemon

    #  Log the full User-Name attribute, as it was found in the request.
    #
    # allowed values: {no, yes}
    #
    stripped_names = no

    #  Log authentication requests to the log file.
    #
    #  allowed values: {no, yes}
    #
    auth = no

    #  Log passwords with the authentication requests.
    #  auth_badpass  - logs password if it's rejected
    #  auth_goodpass - logs password if it's correct
    #
    #  allowed values: {no, yes}
    #
    auth_badpass = no
    auth_goodpass = no
}

#  The program to execute to do concurrency checks.
checkrad = ${sbindir}/checkrad

# SECURITY CONFIGURATION
#
#  There may be multiple methods of attacking on the server.  This
#  section holds the configuration items which minimize the impact
#  of those attacks
#
security {
    #
    #  max_attributes: The maximum number of attributes
    #  permitted in a RADIUS packet.  Packets which have MORE
    #  than this number of attributes in them will be dropped.
    #
    #  If this number is set too low, then no RADIUS packets
    #  will be accepted.
    #
    #  If this number is set too high, then an attacker may be
    #  able to send a small number of packets which will cause
    #  the server to use all available memory on the machine.
    #
    #  Setting this number to 0 means "allow any number of attributes"
    max_attributes = 200

    #
    #  reject_delay: When sending an Access-Reject, it can be
    #  delayed for a few seconds.  This may help slow down a DoS
    #  attack.  It also helps to slow down people trying to brute-force
    #  crack a users password.
    #
    #  Setting this number to 0 means "send rejects immediately"
    #
    #  If this number is set higher than 'cleanup_delay', then the
    #  rejects will be sent at 'cleanup_delay' time, when the request
    #  is deleted from the internal cache of requests.
    #
    #  Useful ranges: 1 to 5
    reject_delay = 1

    #
    #  status_server: Whether or not the server will respond
    #  to Status-Server requests.
    #
    #  When sent a Status-Server message, the server responds with
    #  an Access-Accept or Accounting-Response packet.
    #
    #  This is mainly useful for administrators who want to "ping"
    #  the server, without adding test users, or creating fake
    #  accounting packets.
    #
    #  It's also useful when a NAS marks a RADIUS server "dead".
    #  The NAS can periodically "ping" the server with a Status-Server
    #  packet.  If the server responds, it must be alive, and the
    #  NAS can start using it for real requests.
    #
    #  See also raddb/sites-available/status
    #
    status_server = yes
}

# PROXY CONFIGURATION
#
#  proxy_requests: Turns proxying of RADIUS requests on or off.
#
#  The server has proxying turned on by default.  If your system is NOT
#  set up to proxy requests to another server, then you can turn proxying
#  off here.  This will save a small amount of resources on the server.
#
#  If you have proxying turned off, and your configuration files say
#  to proxy a request, then an error message will be logged.
#
#  To disable proxying, change the "yes" to "no", and comment the
#  $INCLUDE line.
#
#  allowed values: {no, yes}
#
proxy_requests  = yes
$INCLUDE proxy.conf


# CLIENTS CONFIGURATION
#
#  Client configuration is defined in "clients.conf".  
#

#  The 'clients.conf' file contains all of the information from the old
#  'clients' and 'naslist' configuration files.  We recommend that you
#  do NOT use 'client's or 'naslist', although they are still
#  supported.
#
#  Anything listed in 'clients.conf' will take precedence over the
#  information from the old-style configuration files.
#
$INCLUDE clients.conf


# THREAD POOL CONFIGURATION
#
#  The thread pool is a long-lived group of threads which
#  take turns (round-robin) handling any incoming requests.
#
#  You probably want to have a few spare threads around,
#  so that high-load situations can be handled immediately.  If you
#  don't have any spare threads, then the request handling will
#  be delayed while a new thread is created, and added to the pool.
#
#  You probably don't want too many spare threads around,
#  otherwise they'll be sitting there taking up resources, and
#  not doing anything productive.
#
#  The numbers given below should be adequate for most situations.
#
thread pool {
    #  Number of servers to start initially --- should be a reasonable
    #  ballpark figure.
    start_servers = 5

    #  Limit on the total number of servers running.
    #
    #  If this limit is ever reached, clients will be LOCKED OUT, so it
    #  should NOT BE SET TOO LOW.  It is intended mainly as a brake to
    #  keep a runaway server from taking the system with it as it spirals
    #  down...
    #
    #  You may find that the server is regularly reaching the
    #  'max_servers' number of threads, and that increasing
    #  'max_servers' doesn't seem to make much difference.
    #
    #  If this is the case, then the problem is MOST LIKELY that
    #  your back-end databases are taking too long to respond, and
    #  are preventing the server from responding in a timely manner.
    #
    #  The solution is NOT do keep increasing the 'max_servers'
    #  value, but instead to fix the underlying cause of the
    #  problem: slow database, or 'hostname_lookups=yes'.
    #
    #  For more information, see 'max_request_time', above.
    #
    max_servers = 32

    #  Server-pool size regulation.  Rather than making you guess
    #  how many servers you need, FreeRADIUS dynamically adapts to
    #  the load it sees, that is, it tries to maintain enough
    #  servers to handle the current load, plus a few spare
    #  servers to handle transient load spikes.
    #
    #  It does this by periodically checking how many servers are
    #  waiting for a request.  If there are fewer than
    #  min_spare_servers, it creates a new spare.  If there are
    #  more than max_spare_servers, some of the spares die off.
    #  The default values are probably OK for most sites.
    #
    min_spare_servers = 3
    max_spare_servers = 10

    #  There may be memory leaks or resource allocation problems with
    #  the server.  If so, set this value to 300 or so, so that the
    #  resources will be cleaned up periodically.
    #
    #  This should only be necessary if there are serious bugs in the
    #  server which have not yet been fixed.
    #
    #  '0' is a special value meaning 'infinity', or 'the servers never
    #  exit'
    max_requests_per_server = 0
}

# MODULE CONFIGURATION
#
#  The names and configuration of each module is located in this section.
#
#  After the modules are defined here, they may be referred to by name,
#  in other sections of this configuration file.
#
modules {
    #
    #  Each module has a configuration as follows:
    #
    #    name [ instance ] {
    #        config_item = value
    #        ...
    #    }
    #
    #  The 'name' is used to load the 'rlm_name' library
    #  which implements the functionality of the module.
    #
    #  The 'instance' is optional.  To have two different instances
    #  of a module, it first must be referred to by 'name'.
    #  The different copies of the module are then created by
    #  inventing two 'instance' names, e.g. 'instance1' and 'instance2'
    #
    #  The instance names can then be used in later configuration
    #  INSTEAD of the original 'name'.  See the 'radutmp' configuration
    #  for an example.
    #

    #
    #  As of 2.0.5, most of the module configurations are in a
    #  sub-directory.  Files matching the regex /[a-zA-Z0-9_.]+/
    #  are loaded.  The modules are initialized ONLY if they are
    #  referenced in a processing section, such as authorize,
    #  authenticate, accounting, pre/post-proxy, etc.
    #
    $INCLUDE ${confdir}/modules/

    #  Extensible Authentication Protocol
    #
    #  For all EAP related authentications.
    #  Now in another file, because it is very large.
    #
    $INCLUDE eap.conf

    #  Include another file that has the SQL-related configuration.
    #  This is another file only because it tends to be big.
    #
    $INCLUDE sql.conf

    #
    #  This module is an SQL enabled version of the counter module.
    #
    #  Rather than maintaining seperate (GDBM) databases of
    #  accounting info for each counter, this module uses the data
    #  stored in the raddacct table by the sql modules. This
    #  module NEVER does any database INSERTs or UPDATEs.  It is
    #  totally dependent on the SQL module to process Accounting
    #  packets.
    #
#    $INCLUDE sql/mysql/counter.conf

    #
    #  IP addresses managed in an SQL table.
    #
#    $INCLUDE sqlippool.conf
}

# Instantiation
#
#  This section orders the loading of the modules.  Modules
#  listed here will get loaded BEFORE the later sections like
#  authorize, authenticate, etc. get examined.
#
#  This section is not strictly needed.  When a section like
#  authorize refers to a module, it's automatically loaded and
#  initialized.  However, some modules may not be listed in any
#  of the following sections, so they can be listed here.
#
#  Also, listing modules here ensures that you have control over
#  the order in which they are initalized.  If one module needs
#  something defined by another module, you can list them in order
#  here, and ensure that the configuration will be OK.
#
instantiate {
    #
    #  Allows the execution of external scripts.
    #  The entire command line (and output) must fit into 253 bytes.
    #
    #  e.g. Framed-Pool = `%{exec:/bin/echo foo}`
#    exec

    #
    #  The expression module doesn't do authorization,
    #  authentication, or accounting.  It only does dynamic
    #  translation, of the form:
    #
    #    Session-Timeout = `%{expr:2 + 3}`
    #
    #  So the module needs to be instantiated, but CANNOT be
    #  listed in any other section.  See 'doc/rlm_expr' for
    #  more information.
    #
    expr

    #
    # We add the counter module here so that it registers
    # the check-name attribute before any module which sets
    # it
#    daily
    expiration
    logintime

    # subsections here can be thought of as "virtual" modules.
    #
    # e.g. If you have two redundant SQL servers, and you want to
    # use them in the authorize and accounting sections, you could
    # place a "redundant" block in each section, containing the
    # exact same text.  Or, you could uncomment the following
    # lines, and list "redundant_sql" in the authorize and
    # accounting sections.
    #
    #redundant redundant_sql {
    #    sql1
    #    sql2
    #}
}

######################################################################
#
#    Policies that can be applied in multiple places are listed
#    globally.  That way, they can be defined once, and referred
#    to multiple times.
#
######################################################################
$INCLUDE policy.conf

######################################################################
#
#    Load virtual servers.
#
#    This next $INCLUDE line loads files in the directory that
#    match the regular expression: /[a-zA-Z0-9_.]+/
#
#    It allows you to define new virtual servers simply by placing
#    a file into the raddb/sites-enabled/ directory.
#
$INCLUDE sites-enabled/

Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

2. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 12:05 
clients.conf:

# -*- text -*-
##
## clients.conf -- client configuration directives
##
##    $Id$

#######################################################################
#
#  Define RADIUS clients (usually a NAS, Access Point, etc.).

#
#  Defines a RADIUS client.
#
#  '127.0.0.1' is another name for 'localhost'.  It is enabled by default,
#  to allow testing of the server after an initial installation.  If you
#  are not going to be permitting RADIUS queries from localhost, we suggest
#  that you delete, or comment out, this entry.
#
#

#
#  Each client has a "short name" that is used to distinguish it from
#  other clients.
#
#  In version 1.x, the string after the word "client" was the IP
#  address of the client.  In 2.0, the IP address is configured via
#  the "ipaddr" or "ipv6addr" fields.  For compatibility, the 1.x
#  format is still accepted.
#
client localhost {
    #  Allowed values are:
    #    dotted quad (1.2.3.4)
    #       hostname    (radius.example.com)
    ipaddr = 127.0.0.1

    #  OR, you can use an IPv6 address, but not both
    #  at the same time.
#    ipv6addr = ::    # any.  ::1 == localhost

    #
    #  A note on DNS:  We STRONGLY recommend using IP addresses
    #  rather than host names.  Using host names means that the
    #  server will do DNS lookups when it starts, making it
    #  dependent on DNS.  i.e. If anything goes wrong with DNS,
    #  the server won't start!
    #
    #  The server also looks up the IP address from DNS once, and
    #  only once, when it starts.  If the DNS record is later
    #  updated, the server WILL NOT see that update.
    #

    #  One client definition can be applied to an entire network.
    #  e.g. 127/8 should be defined with "ipaddr = 127.0.0.0" and
    #  "netmask = 8"
    #
    #  If not specified, the default netmask is 32 (i.e. /32)
    #
    #  We do NOT recommend using anything other than 32.  There
    #  are usually other, better ways to acheive the same goal.
    #  Using netmasks of other than 32 can cause security issues.
    #
    #  You can specify overlapping networks (127/8 and 127.0/16)
    #  In that case, the smallest possible network will be used
    #  as the "best match" for the client.
    #
    #  Clients can also be defined dynamically at run time, based
    #  on any criteria.  e.g. SQL lookups, keying off of NAS-Identifier,
    #  etc.
    #  See raddb/sites-available/dynamic-clients for details.
    #

#    netmask = 32

    #
    #  The shared secret use to "encrypt" and "sign" packets between
    #  the NAS and FreeRADIUS.  You MUST change this secret from the
    #  default, otherwise it's not a secret any more!
    #
    #  The secret can be any string, up to 8k characters in length.
    #
    #  Control codes can be entered vi octal encoding,
    #    e.g. "\101\102" == "AB"
    #  Quotation marks can be entered by escaping them,
    #    e.g. "foo\"bar"
    #
    #  A note on security:  The security of the RADIUS protocol
    #  depends COMPLETELY on this secret!  We recommend using a
    #  shared secret that is composed of:
    #
    #    upper case letters
    #    lower case letters
    #    numbers
    #
    #  And is at LEAST 8 characters long, preferably 16 characters in
    #  length.  The secret MUST be random, and should not be words,
    #  phrase, or anything else that is recognizable.
    #
    #  The default secret below is only for testing, and should
    #  not be used in any real environment.
    #
    secret        = test

    #
    #  Old-style clients do not send a Message-Authenticator
    #  in an Access-Request.  RFC 5080 suggests that all clients
    #  SHOULD include it in an Access-Request.  The configuration
    #  item below allows the server to require it.  If a client
    #  is required to include a Message-Authenticator and it does
    #  not, then the packet will be silently discarded.
    #
    #  allowed values: yes, no
    require_message_authenticator = no

    #
    #  The short name is used as an alias for the fully qualified
    #  domain name, or the IP address.
    #
    #  It is accepted for compatibility with 1.x, but it is no
    #  longer necessary in 2.0
    #
#    shortname    = localhost

    #
    # the following three fields are optional, but may be used by
    # checkrad.pl for simultaneous use checks
    #

    #
    # The nastype tells 'checkrad.pl' which NAS-specific method to
    #  use to query the NAS for simultaneous use.
    #
    #  Permitted NAS types are:
    #
    #    cisco
    #    computone
    #    livingston
    #    max40xx
    #    multitech
    #    netserver
    #    pathras
    #    patton
    #    portslave
    #    tc
    #    usrhiper
    #    other        # for all other types

    #
    nastype     = other    # localhost isn't usually a NAS...

    #
    #  The following two configurations are for future use.
    #  The 'naspasswd' file is currently used to store the NAS
    #  login name and password, which is used by checkrad.pl
    #  when querying the NAS for simultaneous use.
    #
#    login       = !root
#    password    = someadminpas

    #
    #  As of 2.0, clients can also be tied to a virtual server.
    #  This is done by setting the "virtual_server" configuration
    #  item, as in the example below.
    #
#    virtual_server = home1
}

Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

3. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 12:06 
sql.conf:

# -*- text -*-
##
## sql.conf -- SQL modules
##
##    $Id$

######################################################################
#
#  Configuration for the SQL module
#
#  The database schemas and queries are located in subdirectories:
#
#    sql/DB/schema.sql    Schema
#    sql/DB/dialup.conf    Basic dialup (including policy) queries
#    sql/DB/counter.conf    counter
#    sql/DB/ippool.conf    IP Pools in SQL
#    sql/DB/ippool.sql    schema for IP pools.
#
#  Where "DB" is mysql, mssql, oracle, or postgresql.
#

sql {
    #
    #  Set the database to one of:
    #
    #    mysql, mssql, oracle, postgresql
    #
    database = "postgresql"

    #
    #  Which FreeRADIUS driver to use.
    #
    driver = "rlm_sql_${database}"

    # Connection info:
    server = "localhost"
    port = 5432
    login = "raduser"
    password = ""

    # Database table configuration for everything except Oracle
    radius_db = "raddatab"
    # If you are using Oracle then use this instead
        # radius_db = "(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=localhost)(PORT=1521))(CONNECT_DATA=(SID=your_sid)))"

    # If you want both stop and start records logged to the
    # same SQL table, leave this as is.  If you want them in
    # different tables, put the start table in acct_table1
    # and stop table in acct_table2
    acct_table1 = "radacct"
    acct_table2 = "radacct"

    # Allow for storing data after authentication
    postauth_table = "radpostauth"

    authcheck_table = "radcheck"
    authreply_table = "radreply"

    groupcheck_table = "radgroupcheck"
    groupreply_table = "radgroupreply"

    # Table to keep group info
    usergroup_table = "radusergroup"

    # If set to 'yes' (default) we read the group tables
    # If set to 'no' the user MUST have Fall-Through = Yes in the radreply table
    # read_groups = yes

    # Remove stale session if checkrad does not see a double login
    deletestalesessions = yes

    # Print all SQL statements when in debug mode (-x)
    sqltrace = no
    sqltracefile = ${logdir}/sqltrace.sql

    # number of sql connections to make to server
    num_sql_socks = 5

    # number of seconds to dely retrying on a failed database
    # connection (per_socket)
    connect_failure_retry_delay = 60

    # lifetime of an SQL socket.  If you are having network issues
    # such as TCP sessions expiring, you may need to set the socket
    # lifetime.  If set to non-zero, any open connections will be
    # closed "lifetime" seconds after they were first opened.
    lifetime = 0

    # Maximum number of queries used by an SQL socket.  If you are
    # having issues with SQL sockets lasting "too long", you can
    # limit the number of queries performed over one socket.  After
    # "max_qeuries", the socket will be closed.  Use 0 for "no limit".
    max_queries = 0

    # Set to 'yes' to read radius clients from the database ('nas' table)
    # Clients will ONLY be read on server startup.  For performance
    # and security reasons, finding clients via SQL queries CANNOT
    # be done "live" while the server is running.
    #
    #readclients = yes

    # Table to keep radius client info
    nas_table = "nas"

    # Read driver-specific configuration
    $INCLUDE sql/${database}/dialup.conf
}

Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

4. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от PavelR (??) on 18-Июл-09, 13:27 

Научись команде "grep -v".
Читать портянки комментариев в конфиг файлах мало кому интересно.
Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

5. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 13:32 
ок, переделаю)
Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

6. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 13:37 
clients.conf:

client localhost {
    ipaddr = 127.0.0.1
    secret        = test    
    require_message_authenticator = no
    nastype     = other    # localhost isn't usually a NAS...
}


Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

7. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 13:42 
radius.conf:
prefix = /usr/local/
exec_prefix = ${prefix}
sysconfdir = ${prefix}/etc
localstatedir = /var
sbindir = ${exec_prefix}/sbin
logdir = /var/log
raddbdir = ${sysconfdir}/raddb
radacctdir = ${logdir}/radacct
name = radiusd

confdir = ${raddbdir}
run_dir = ${localstatedir}/run/${name}

db_dir = ${raddbdir}

libdir = /usr/local/lib/freeradius-2.1.6
pidfile = ${run_dir}/${name}.pid
user = freeradius
group = freeradius
max_request_time = 30
cleanup_delay = 5
max_requests = 1024
listen {
    type = auth
    ipaddr = *
    port = 1812
}

listen {
    ipaddr = *
    port = 0
    type = acct
}

hostname_lookups = no
allow_core_dumps = no

regular_expressions    = yes
extended_expressions    = yes
log {
    destination = files
    file = ${logdir}/radius.log
    syslog_facility = daemon
    stripped_names = no
    auth = no
    auth_badpass = no
    auth_goodpass = no
}

checkrad = ${sbindir}/checkrad

security {
    max_attributes = 200
    status_server = yes
}

proxy_requests  = yes
$INCLUDE proxy.conf

$INCLUDE clients.conf
thread pool {
    start_servers = 5
    max_servers = 32
    min_spare_servers = 3
    max_spare_servers = 10
    max_requests_per_server = 0
}
modules {
    $INCLUDE ${confdir}/modules/
    $INCLUDE eap.conf
    $INCLUDE sql.conf

}

instantiate {
    expr

    expiration
    logintime

}

$INCLUDE policy.conf

$INCLUDE sites-enabled/

Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

8. "Freeradius 2.1.6 не коннектится к базе PostgreSQL"  +/
Сообщение от sba (ok) on 18-Июл-09, 19:32 
Разобрался сам... Оказалось, надо править ещё один конфигурационник ./raddb/sites-aviable/default, настроить на использование sql.
Высказать мнение | Ответить | Правка | Наверх | Cообщить модератору

Архив | Удалить

Индекс форумов | Темы | Пред. тема | След. тема




Спонсоры:
MIRhosting
Fornex
Hosting by Ihor
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2019 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру