Доброго времени суток, всем тут присутствующим!Вот какая проблемка возникла, необходимо организовать доступ к vpn-gprs через Cisco 805 и siemens mc35, пример настройки циски взяла с http://www.cisco.com/en/US/docs/routers/access/800/805/softw...
На текущий момент все остновилось на попытке достучаться до точки впн-доступа 192.168.1.100
Может кто-то подскажет что в этом все не так и как это исправить?
Заранее огроменное спасибочки :)
Gprs1#sh hard
Cisco Internetwork Operating System Software
IOS (tm) C805 Software (C805-Y6-MW), Version 12.2(15)T11, RELEASE SOFTWARE (fc2)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 31-Jan-04 13:17 by nmasa
Image text-base: 0x0017F000, data-base: 0x00874000
ROM: TinyROM version 1.4(1)
gprs5 uptime is 1 day, 6 hours, 10 minutes
System returned to ROM by reload
System image file is "flash:c805-y6-mw.122-15.T11.bin"
Cisco C805 (MPC850) processor (revision 0) with 48456K bytes of virtual memory.
Processor board ID FOC081519GJ (2294284437)
CPU part number 0x2101
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial(sync/async) network interface(s)
8M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)
Configuration register is 0x2102
Gprs1#sh dial
Di1 - dialer type = DIALER PROFILE
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
Number of active calls = 0
Dial String Successes Failures Last DNIS Last status
*99***1# 0 0 00:42:16 failed Default
Se0 - dialer type = IN-BAND ASYNC NO-PARITY
Dialer pool 1, priority 0
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
gprs1#sh int dial 1
Dialer1 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address is 192.168.100.1/24
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
DTR is pulsed for 1 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 1d05h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Gprs1#sh run
Building configuration...
Current configuration : 2060 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname gprs1
!
boot system flash
logging queue-limit 100
enable secret 5 $1$wmxOJvKyMh2OCxQuVL9Rglcb.
enable password 7 030F581F0E24424F0B1500
!
ip subnet-zero
no ip domain lookup
!
chat-script reset "" \d\d\d+++\d\d\d
chat-script ks TIMEOUT 90 "" AT+CGDCONT=1,"ip","somebody.kyivstar.net" OK ATDT\T CONNECT
modemcap entry GPRS:FD=Z
modemcap entry usr-modem:MSC=AT+CGDCONT=1,"IP","SOMEBODY.KYIVSTAR.NET"
!
!
!
interface Ethernet0
ip address 10.10.1.1 255.255.255.252
no cdp enable
hold-queue 32 in
!
interface Serial0
physical-layer async
no ip address
encapsulation ppp
dialer in-band
dialer pool-member 1
dialer-group 1
async mode dedicated
no keepalive
ppp authentication chap pap
ppp chap hostname igprs
ppp chap password 7 08284B5E1B0A
ppp pap sent-username igprs password 7 04520C161D32
!
interface Dialer1
ip address 192.168.100.1 255.255.255.0
encapsulation ppp
dialer pool 1
dialer string "*99***1#" modem-script ks
dialer-group 1
no peer default ip address
no cdp enable
ppp authentication chap pap
ppp chap hostname igprs
ppp chap password 7 10470E091704
ppp chap refuse
ppp pap sent-username igprs password 7 121002070018
!
ip classless
ip route 192.168.1.100 255.255.255.255 Dialer1
no ip http server
!
!
logging trap debugging
dialer-list 1 protocol ip permit
no cdp run
!
line con 0
stopbits 1
line 1
modem InOut
transport input all
stopbits 1
flowcontrol hardware
line vty 0 4
password 7 030F5A181F0E37455C1D0C041B
login
!
end
gprs1#ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Gprs1#sh log
Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 ove
rruns, xml disabled)
Console logging: level debugging, 1994 messages logged, xml disabled
Monitor logging: level debugging, 0 messages logged, xml disabled
Buffer logging: level debugging, 1994 messages logged, xml disabled
Logging Exception size (2048 bytes)
Count and timestamp logging messages: disabled
Trap logging: level debugging, 1909 message lines logged
Log Buffer (2048 bytes):
1d06h: Se0 DDR: rotor dialout [best] least recent failure is also most recent failure
1d06h: Se0 DDR: rotor dialout [best] also has most recent failure
1d06h: Se0 DDR: rotor dialout [best]
1d06h: Se0 DDR: Dialing cause ip (s=192.168.100.1, d=192.168.1.100)
1d06h: Se0 DDR: Attempting to dial *99***1#
1d06h: CHAT1: Attempting async line dialer script
1d06h: CHAT1: Dialing using Modem script: ks & System script: none
1d06h: CHAT1: process started
1d06h: CHAT1: Asserting DTR
1d06h: CHAT1: Chat script ks started
1d06h: CHAT1: Sending string: AT+CGDCONT=1,"IP","somebody.kyivstar.net"
1d06h: CHAT1: Expecting string: OK
1d06h: CHAT1: Timeout expecting: OK
1d06h: CHAT1: Chat script ks finished, status = Connection timed out; remote host not
responding
И на этом полный тупик... %)
gprs1#sh line 1
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
1 TTY 9600/9600 - inout - - - 0 0 0/0 Se0
Idle
Line 1, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits
Status: No Exit Banner, CTS Raised, Modem Speed Locked
Capabilities: Hardware Flowcontrol In, Hardware Flowcontrol Out
Modem Callout, Modem RI is CD, Line is permanent async interface
Modem state: Idle
Modem hardware state: CTS noDSR DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
00:10:00 never none not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: never
Editing is enabled.
History is enabled, history size is 20.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are telnet.
Allowed output transports are telnet.
Preferred transport is telnet.
No output characters are padded
No special data dispatching characters