Обсуждение статьи тематического каталога: Установка мультипортовой карты Moxa Smartio C104HPCI под FreeBSD 4.7 (freebsd multiport serial moxa)Ссылка на текст статьи: https://www.opennet.ru/base/sys/moxa_bsd2.txt.html
Не могу понят почему но не получилось, всё зделал как указано.
И всё равно psi0: <unknown kard> (vendor=0x114f, dev=0x0028) at 10.0 irq 10.
У меня определилась как mx0: <Moxa CP-168u series> port ... итд.И как ни странно ставил совсем другим способом, только потом уже прочитал что есть сия информация..
В самом драйвере была дана инструкция по установке=============================================================================
MOXA Smartio/Industio Family Device Driver Installation Guide
for FreeBSD 4.x/5.x
Copyright (C) 2005, Moxa Technologies Co, Ltd.
=============================================================================
Date:Content
0. Note
1. Introduction
2. System Requirement
3. Installation
3.1 Hardware installation
3.2 Driver files
3.3 Device naming convention
3.4 Module driver configuration
3.7 Custom configuration
3.8 Verify driver installation
4. Utilities
5. Setserial
6. Troubleshooting-----------------------------------------------------------------------------
0. Note
0.1 Installation step summary.
Hardware installation:
Refer to the "3.1 Hardware installation".
Software/driver installation:
0.2.1 Extract the Moxa driver: Refer to the "3.2 Driver files".
-----------------------------------------------------------------------------
1. IntroductionThe Smartio/Industio family FreeBSD driver supports following multiport
boards.Smatio:
C104H, C104HS, C104H/PCI, C104HS/PCI,
C168H, C168HS, C168H/PCI, C168P,
CI-104J, CI-104JS
CP-104UL,
CP-104JU,
CP-168U,Industio:
CI-132, CI-132I, CI-123IS,
CI-134, CI-134I, CI-134IS,
CP-132, CP-132I, CP132S, CP-132IS,
CP-114, CP-114I, CP-114S, CP-114IS,
CP-132U-I, CP-132UL,
CP-134U, CP-134U-II
CT-114I,This driver and installation procedure have been developed upon FreeBSD
4.6/5.3 and compatible to all 4.x/5.x. This driver supports Intel x86
hardware platform. However, if compatibility problem occurs, please contact
Moxa at support@moxa.com.In addition to device driver, useful utilities are also provided in this
version. They are
- msdiag Diagnostic program for displaying installed Moxa
Smartio/Industio boards.
- io-irq.exe Configuration program to setup ISA boards. Please note that
this program can only be executed under DOS.All the drivers and utilities are published in form of source code under
BSD License in this version. Please refer to BSD License announcement
in each source code file for more detail.This version of driver can be installed as Loadable Module (Module driver).
You may refer to following installation procedure. Before you install
the driver, please refer to hardware installation procedure in the
User's Manual.-----------------------------------------------------------------------------
2. System Requirement
- Hardware platform: Intel x86 machine
- FreeBSD version: 4.x/5.x
- Package Requirement: gcc, kernel source
- Maximum 4 boards can be installed in combination-----------------------------------------------------------------------------
3. Installation3.1 Hardware installation
3.2 Driver files
3.3 Device naming convention
3.4 Module driver configuration
3.7 Custom configuration
3.8 Verify driver installation
3.1 Hardware installationThere are two types of buses, ISA and PCI, for Smartio/Industio
family multiport board.ISA board
---------
You'll have to configure CAP address, I/O address, Interrupt Vector
as well as IRQ before installing this driver. Please refer to hardware
installation procedure in User's Manual before proceed any further.
Please make sure the JP1 is open after the ISA board is set properly.PCI board
---------
You may need to adjust IRQ usage in BIOS to avoid from IRQ conflict
with other ISA devices. Please refer to hardware installation
procedure in User's Manual in advance.PCI IRQ Sharing
-----------
Each port within the same multiport board shares the same IRQ. Up to
4 Moxa Smartio/Industio PCI Family multiport boards can be installed
together on one system and they can share the same IRQ.
3.2 Driver filesThe driver file may be obtained from CD-ROM or Web site. The
first step, anyway, is to copy driver file "mxbsd_<version>.tgz"
into specified directory. e.g. /moxa. The execute commands as below.<copy mxbsd_<version>.tgz into /moxa directory>
# cd /moxa
# tar xvfz mxbsd_<version>.tgz
3.3 Device naming convention
You may find all the driver and utilities files in ./moxa
Dialin and callout port
-----------------------
This driver remains traditional serial device properties. There are
two special file name for each serial port. One is dial-in port
which is named "ttyMxx". For callout port, the naming convention
is "cumxx".Device naming when more than 2 boards installed
-----------------------------------------------
Naming convention for each Smartio/Industio multiport board is
pre-defined as below.Board Num. Dial-in Port Callout port
1st board ttyM0 - ttyM7 cum0 - cum7
2nd board ttyM8 - ttyM15 cum8 - cum15
3rd board ttyM16 - ttyM23 cum16 - cum23
4th board ttyM24 - ttym31 cum24 - cum313.4 Module driver configuration
------------- Prepare to use the MOXA driver--------------------
3.4.1 Create tty device with correct major number
---------------NOTE----------------
This step is only for FreeBSD 4.x.
-----------------------------------
Before using MOXA driver, your system must have the tty devices
which are created with driver's major number. We offer one shell
script "msmknod" to simplify the procedure.
This step is only needed to be executed once. But you still
need to do this procedure when:
a. Your total installed MOXA boards number is changed. Maybe you
add/delete one MOXA board.
b. You want to change the tty name. This needs to modify the
shell script "msmknod"The procedure is:
# cd /moxa/mxser/driver
# ./msmknodMsmknod will delete any special files occupying the same device
naming.
3.4.2 If you'd like to drive Smartio/Industio ISA boards in the system,
you'll have to add parameter to specify CAP address of given
board in file config.h.
a. # cd /moxa/mxser/driver
# vi config.h
b. Find the array mxserBoardCAP[] as below.static int mxserBoardCAP[]
= {0x00, 0x00, 0x00, 0x00};c. Change the address within this array using vi. For
example, to driver 2 ISA boards with CAP address
0x280 and 0x180 as 1st and 2nd board. Just to change
the source code as follows.static int mxserBoardCAP[]
= {0x280, 0x180, 0x00, 0x00};
3.4.3 Build the MOXA driver and utilities
Before using the MOXA driver and utilities, you need compile the
all the source code. This step is only need to be executed once.
Find "Makefile" in /moxa, then run# make clean; make install
The driver files "mx.ko" and utilities will be properly compiled
and copied to system directories respectively.
------------- Load MOXA driver--------------------
3.4.4 Load the MOXA driver# kldload mx
will activate the module driver. You may run "kldstat" to check
if "mx" is activated.
------------- Load MOXA driver on boot --------------------
3.4.5 For the above description, you may manually execute "kldload mx"
to activate this driver and run "kldunload mx" to remove it.
However, it's better to have a boot time configuration to
eliminate manual operation. Boot time configuration can be
achieved by loader.conf file.
Run following command for setting loader.conf files.# vi /boot/loader.conf
Add the following line to the file:
mx_load="YES"Reboot and check if mx.ko activated by "kldstat" command.
3.7 Custom configuration
Although this driver already provides you default configuration, you
still can change the device name. The instruction to
change these parameters are shown as below.Change Major number
-------------------
If major number 30 and 35 had been occupied, you may have to select
2 free major numbers for this driver. There are 3 steps to change
major numbers.3.7.1 Find free major numbers
Please select 2 major numbers that are available.
e.g. 40, 45.
3.7.2 Create special files
(This is only for FreeBSD 4.x)
Run /moxa/mxser/driver/msmknod to create special files with
specified major numbers.
3.7.3 Modify driver with new major number
Run vi to open /moxa/mxser/driver/mx.c. Locate the line
contains "CDEV_MAJOR". Change the content as below.
#define CDEV_MAJOR 33
3.7.4 Run "make install" in /moxa/mxser/driver.-----------------------------------------------------------------------------
4. Utilities
There are 1 utility contained in this driver. It is diag.
The 1 utility is released in form of source code. They should
be compiled into executable file and copied into /usr/bin.Before using these utilities, please load driver (refer 3.4) and
make sure you had run the "msmknod" utility.msdiag - Diagnostic
--------------------
This utility provides the function to display what Moxa Smartio/Industio
board found by driver in the system.-----------------------------------------------------------------------------