The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

ep ()
  • >> ep (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    ep
    
     - Ethernet driver for 3Com Etherlink III (3c5x9) interfaces
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following line in your kernel configuration file:
    device ep

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_ep_load="YES"
    
     

    DESCRIPTION

    The device driver supports network adapters based on the 3Com 3C5x9 Etherlink III Parallel Tasking chipset.

    Various models of these cards come with a different assortment of connectors:

    AUI/DIX
    Standard 15 pin connector, also known as 10base5 (thick-net)
    10Base2
    BNC, also known as thin-net
    10BaseT
    UTP, also known as twisted pair

    The default port to use is the port that has been selected with the setup utility. To override this, use the following media options with ifconfig(8) or in your /etc/rc.conf file.

    10base5/AUI
    Use the AUI port.
    10base2/BNC
    Use the BNC port.
    10baseT/UTP
    Use the UTP port.

    If there are multiple cards in the computer, they are searched for in the following order: bus, slot, then Ethernet address.  

    HARDWARE

    The driver supports Ethernet adapters based on the 3Com 3C5x9 Etherlink III Parallel Tasking chipset, including:

     

    NOTES

    The 3c509 card has no jumpers to set the address. 3Com supplies software to set the address of the card in software. To find the card on the ISA bus, the kernel performs a complex scan operation at IO address 0x110. Beware! Avoid placing other cards at that address!

    Furthermore, the 3c509 should only be configured in EISA mode when installed in a computer that has actual EISA slots (and an EISA-aware BIOS). The normal driver auto-detection support is sufficient for non-EISA systems.

    Many different companies sold the 3Com PC Cards under their own private label. These cards also work.

    The Farallon EtherWave and EtherMac card came in two varieties. The driver supports the 595 and 895 cards. These cards have the blue arrow on the front along with a 3Com logo. The Farallon 595a cards, which have a red arrow on the front, are also called EtherWave and EtherMac. They are supported by the sn(4) driver.  

    DIAGNOSTICS

    "ep0: reset (status: %x)"
    The driver has encountered a FIFO underrun or overrun. The driver will reset the card and the packet will be lost. This is not fatal.
    "ep0: eeprom failed to come ready"
    The eeprom failed to come ready. This probably means the card is wedged.
    "ep0: 3c509 in test mode. Erase pencil mark!"
    This means that someone has scribbled with pencil in the test area on the card. Erase the pencil mark and reboot. (This is not a joke).
    "ep0: I/O space?!
    The driver was unable to allocate the I/O space that it thinks should be there. Look for conflicts with other devices.
    "ep0: irq?!
    The driver could not allocate the interrupt it wanted. Look for conflicts, although sharing interrupts for PC Card is normal.
    "ep0: connectors!
    The driver queried the hardware for what ethernet attachment were present, but the hardware reported none that the driver recognized.
    "ep0: Unable to get Ethernet address!"
    The driver was unable to read the ethernet address from the EEPROM. This is likely the result of the card being wedged.
    "ep0: if_alloc() failed"
    The driver was unable to allocate a ifnet structure. This may happen in extremely low memory conditions.
    "ep0: strange connector type in EEPROM: assuming AUI"
    The driver does not know what to do with the information the EEPROM has about connectors, so it is assuming the worst.
    "ep0: unknown ID 0xXXXXXXXX"
    The driver has found an ID that it believes it supports, but does not have a specific identification string to present to the user.
    "ep0: <%s> at port 0x%03x in EISA mode"
    The 3C509 ISA card is in EISA mode. This message appears to be purely informational.
    "ep0: <%s> at x0%03x in PnP mode"
    This card appears to be in Plug and Play mode. It should be probed as part of the plug and play phase of the ISA probes.
    "ep0: Invalid EEPROM checksum!"
    The EEPROM has a bad checksum, so the driver is ignoring the card.
    "ep0: bus_setup_intr() failed!"
    The driver was unable to setup the interrupt handler. This should never happen.

     

    SEE ALSO

    altq(4), ed(4), el(4), ie(4), intro(4), ng_ether4, vx(4), ifconfig(8)  

    STANDARDS

    are great. There is so many to choose from.  

    BUGS

    Support for the 3Com 3C1 is not working.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HARDWARE
    NOTES
    DIAGNOSTICS
    SEE ALSO
    STANDARDS
    BUGS


    Поиск по тексту MAN-ов: 




    Спонсоры:
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2021 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру