The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

drv_getparm (9)
  • >> drv_getparm (9) ( Solaris man: Ядро )
  •  

    NAME

    drv_getparm - retrieve kernel state information
     
    

    SYNOPSIS

    #include <sys/ddi.h>
    
    
    
    int drv_getparm(unsigned int parm, void *value_p);
    

     

    INTERFACE LEVEL

    Architecture independent level 1 (DDI/DKI).  

    PARAMETERS

    parm

    The kernel parameter to be obtained. Possible values are:

    LBOLT

    Read the value of lbolt. lbolt is a clock_t that is unconditionally incremented by one at each clock tick. No special treatment is applied when this value overflows the maximum value of the signed integral type clock_t. When this occurs, its value will be negative, and its magnitude will be decreasing until it again passes zero. It can therefore not be relied upon to provide an indication of the amount of time that passes since the last system reboot, nor should it be used to mark an absolute time in the system. Only the difference between two measurements of lbolt is significant. It is used in this way inside the system kernel for timing purposes.

    PPGRP

    Read the process group identification number. This number determines which processes should receive a HANGUP or BREAK signal when detected by a driver.

    UPROCP

    Read the process table token value.

    PPID

    Read process identification number.

    PSID

    Read process session identification number.

    TIME

    Read time in seconds.

    UCRED

    Return a pointer to the caller's credential structure.

    value_p

    A pointer to the data space in which the value of the parameter is to be copied.

     

    DESCRIPTION

    Since the release of the Solaris 2.6 operating environment, the drv_getparm() function has been replaced by ddi_get_lbolt(9F), ddi_get_time(9F), and ddi_get_pid(9F).

    The drv_getparm() function verifies that parm corresponds to a kernel parameter that may be read. If the value of parm does not correspond to a parameter or corresponds to a parameter that may not be read, -1 is returned. Otherwise, the value of the parameter is stored in the data space pointed to by value_p.

    The drv_getparm() function does not explicitly check to see whether the device has the appropriate context when the function is called and the function does not check for correct alignment in the data space pointed to by value_p. It is the responsibility of the driver writer to use this function only when it is appropriate to do so and to correctly declare the data space needed by the driver.  

    RETURN VALUES

    The drv_getparm() function returns 0 to indicate success, -1 to indicate failure. The value stored in the space pointed to by value_p is the value of the parameter if 0 is returned, or undefined if -1 is returned. -1 is returned if you specify a value other than LBOLT, PPGRP, PPID, PSID, TIME, UCRED, or UPROCP. Always check the return code when using this function.  

    CONTEXT

    The drv_getparm() function can be called from user context only when using PPGRP, PPID, PSID, UCRED, or UPROCP. It can be called from user, interrupt, or kernel context when using the LBOLT or TIME argument.  

    SEE ALSO

    ddi_get_lbolt(9F), ddi_get_pid(9F), ddi_get_time(9F), buf(9S)

    Writing Device Drivers


     

    Index

    NAME
    SYNOPSIS
    INTERFACE LEVEL
    PARAMETERS
    DESCRIPTION
    RETURN VALUES
    CONTEXT
    SEE ALSO


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру